It takes less than 10 minutes to turn your steerer tube into a portable workshop. Just remove the start nut, drop in the EDC Threadless Carrier. Then, you will be able to store a EDC V2 Tool and the EDC Tire Plug Kit in your stem.
The 20-function EDC V2 Tool is the heart of the Threaded EDC system. It includes a 10 function Multi-Tool, Tire Lever, Chain Breaker, steel spoke keys, quick link storage, and a small and large storage capsule designed to a jabber, tire plugs, and quick link pliers.
The EDC Plug kit is the perfect addition to the EDC tool system. The kit includes a tire jabber and additional plugs. The EDC Threadless Carrier and 70cc Pump will only fit the jabber and tireplugs - no pliers.
The Threadless carrier is only comptible with Fox 38 Performance Elite & Factory series forks that have a steerer tube longer than 245mm.
If the threadless carrier will not fully insert into your fork, then it is likely that the length of your steerer tube is less than the minimum requirement. Please double check your steerer length and compare it to our compatibility list before proceeding.
The pins measure 5mm in diameter.
There are three possibilities for this:
1. Make sure the middle O-ring has been removed from the EDC tool system.
2. Is the mutli tool oriented correctly within the EDC tool body? If it is backward and not meshing will the tire lever, the tool will bulge and will not fit into any holder.
3. Check the steerer tube length, if you there was any force required during installation of the carrier then it is likely under pressure and flexing. This means your fork steerer length is too short, or it is an incompatible fork.
It is possible with some pre-requisite checks.
1. Steerer ID meets the compatibility requirements for the Threadless carrier (Min ID: 24.25mm)
2. Steerer does not neck internally at any point. You can check this by running a straight edge down & against the internal wall of your steerer. If it deflects then it necks and is not compatible.
3. Steerer is within our compatible length range. 185mm-265mm
4. Your current Top cap will need to replace the 1-1/2 plug supplied with our Threadless carriers. So check that the top cap fits flush without rocking, in the underside of the fork steerer.
If you can confirm all of these requirements are good then you should have no issue installing our threadless carrier in your straight steerer fork.
Unfortunately, none of our EDC options are compatible with forks with carbon steerer tubes.
The plug and bacon strips with fit within the small storage capsule and then fit into the threadless carrier. The Pliers, the large storage capsule or a c02 cartridge do not fit in the threadless carrier.
The chainbreaker is mounted to the tire lever. Using the T25 in the multi tool, loosen the chainbreaker and rotate it perpendicular to the tire lever. Using the 3mm in the multi tool, back the pin off, then you can position the tool around the chainlink and thread to pin back in until you have broken the chain!
Overall rating: 4.7272725 / 5 from 165 reviews.
The EDC Threadless Carrier is highly praised for its ease of installation, outstanding quality, and secure access to tools. Customers appreciate its smooth fit and compact design, making it a convenient and reliable tool carrier for the trail.
Review topics: ["fit","quality","looks","issues","design","improvement","instructions","post","service","works","tool","install","carrier","tube","holds","access","buy","system","kit","nuts","idea","noise","addition","accessory"].
"Works awesome. I really like the product. The build seemed cheap. The screw I needed had bad threads making install super hard. They could have included a higher quality screw for the price of the product. The carrier was much lighter than expected which is probably fine but didn’t give me a sense of confidence when installing because it seemed cheap."
"Great tool and easy to install. Would highly recommend to anyone looking for a tool to take on the trail."
"Install was easy and works as advertised. Well made product"
"This is a great piece of kit and solves the problem of carrying a multi tool, or really forgetting a multi tool. Good quality and have used others on another bike. My only complaint is it is too long and requires too long a steerer tube, They should make a shorter version by like 20 millimeters so you don't need a 190mm steerer tube."
"Knocked off a star because the larger storage tube won't fit with the threadless carrier. Otherwise the installation was very straightforward and it seems like a solid product."
"Love it"
"So easy to use and reminds me of bmx parts."
"Great quality. Straightforward installation"
"It was a present for my son who is very happy with it."
"Easy to install and a great way for carrying tools"
